Perkin Elmer Optoelectronics
44370 Christy Street
Fremont
CA94538
USA
Tel: +1 510 979 6500
Fax: +1 510 687 1100
e-mail: sales@perkinelmer.com
http://www.perkinelmer.com

Bravoluz Comercial Ltda
Rua Bom Jesus de Iguape, 5134 - Boqueirão
Curitiba - PR. CEP 81730-020
Telefone: 41-3076-4588
e-mail:contato@bravoluz.com.br

http://www.bravoluz.com.br

Input voltage:

90 – 264V rms. universal input

AC Power Connector:

3 X 0.25” spade tabs

Input Frequency:

47 – 63Hz

Maximum Input Power:

<500W

Maximum Input Current:

<7A rms.

Input Fuse:

8A time lag (T8A 250V HRC 5 X 20mm in line only)

Input Power Factor:

>0.95 (meets the harmonic requirements of EN61000-3-2 class-D)

Mains Earth Leakage Current:

<120uA @120Vrms, <240uA @240Vrms

Maximum Output Voltage:

22Vdc (compensates automatically for lamp voltage up 22V max)

Output Current Range:

4 – 23A (constant current, adjustable by internal pot or remotely)

Output Connections:

2 X 0.25” spade tabs

Over Current Protection:

>25A constant current

Maximum Output Power:

320W lamp + 30W auxiliary / fan

Output Ripple Current:

<2% peak –peak

Lamp Boost Voltage:

>200Vdc

Lamp Ignition Pulse:

Bipolar >+/-15KV wrt ground (30KV peak – peak)

Interface Controls:

Remote Enable / Disable. Auto / Manual mode. Interlock

Remote output current adjust. Current monitor

Interface Signals:

LAMP ON and LAMP REPLACE signals

Auxiliary Outputs:

5V +/-4% @ 1A, 12V+/-4% @ 2A isolated & independent of lamp operation.

Fan Output:

12V +/-4% @ 1A (only present when lamp operating)

Efficiency:

70% (at full power)

Operating Temperature Range:

0 – 45deg.C

Storage Temperature:

-20 to +85deg.C

Over Temperature Protection:

Thermostat shuts psu down if excessive internal temperature.

Air Flow Requirement:

>60cfm

Maximum Operating Humidity:

95% RH non condensing

Shipping Shock & Vibration:

ISTA1A, 2A

Safety Compliance:

UL60601-1, EN60601-1, IEC60601-1, CSA-22.2 No.601-1-M90

CE mark, CB report. (psu requires correct installation) UL file. E193746

Size:

7” X 4.5” X 2.05” (177.8 X 114.2 X 52mm)

CON 2:

Pin 1(+ve) Pin2(-ve): ENABLE INPUT (Isolated from mains and outputs). When psu

used in Manual mode (see CON 4), apply +5V to enable lamp (or 12V via 1K5).

Pin 3(+ve): CURRENT MONITOR. Current shunt (0.005ohm ie 5mV/A) monitors lamp

current ie 100mV = 20A

Pin 4: LAMP REPLACE. Signal to indicate lamp needs replacing when

lamp voltage > 16V. Low output (<1V) when lamp needs replacing.

Open collector transistor output. Should use a 2K pull-up resistor to +12V FAN output.

Pin 5: CURRENT ADJUST. Can be used to remotely adjust output current by

connecting external resistance between pin 5 & 7(0V).

With lamp current set at 21A, with 10K pot fitted, typical results: 5.6K = 19A, 2.2K =

17A, 1.24K = 15A, 750R = 13A, 450R = 11A , 240R =9A 105R = 7A, 12R = 5A

Pin 6: LAMP ON. Signal to indicate lamp is ON (when lamp voltage < 24V).

Low = Lamp ON ( LED indicator can be used via 510R resistor to fan supply voltage

(connector CON 3. Pin 1 or CON 2 pin 8)

High = Lamp OFF (5.1K internal pull-up resistor fitted to12V FAN output, and 7V5

Zener in series with o/p.

Pin 7: 0V. Signal 0V. (referenced to ground). Return for pins 3,4,5,6,8

Pin 8: +12V FAN. Additional fan voltage supply connection in parallel to Con 3

Pin 9: 0V (Return of AUX. 5V)

Pin 10: +5V/1A (auxiliary, floating output. ON when Mains ON, irrespective of lamp)

Pin 11: 0V (Return of AUX. 12V)

Pin 12: +12V/2A (auxiliary, floating output. ON when Mains ON, irrespective of lamp)

Note:Aux outputs are isolated from each other and from the interface 0V and ground

CON 3:

Pin 1: +12V/1A - Can be used for psu fan. Only present when lamp is ON.

Pin 2: 0V ( 12V FAN Return, is referenced to ground)

Note: The fan supply is also available on CON 2 pins 7 & 8.

CON 4:

Pins 1-2: INTERLOCK. Supplied fitted with link. Lamp will shut down if pins open.

Pins 3-4: MANUAL/AUTOMATIC. Supplied with link fitted. If pins open lamp will

only operate using the Enable input. (See CON2 pin1&2). NOTE: pins 2,3 are joined.

Note: CON 4 is referenced to mains voltage therefore creepage / clearance distances to

Earth / ground and output need to be considered according to safety requirements.

Signal Connectors:

CON 2: 12 way, 0.1” pitch, right-angle locking header.

CON 3: 2 way, 0.1” pitch, straight locking header.

CON 4: 4 way. 01” pitch, straight header, fitted with 2 jumper links.

Types fitted are Taicom TKB series

Mating connector housing type:

Taicom type TKB series

or Molex type KK series

Crimp type:

Taicom TK series

or Molex KK series